Review Hot-rolled sheet and coil for the 12 × 1250 × 12000 mm (12x1250x12000) specification. Check material grade, dimensions, inspection documents and delivery requirements before requesting a quotation.
Geometric estimates exclude rolling tolerances, coatings and process losses; hollow and rolled-section references include their own section-table basis. Calculated bar weights use unrounded mass. Values are not measured shipment weights. Confirm length, grade, manufacturing route, packing and supply in the offer; the existing image illustrates the product family.
Reference dimensions: 12 × 1250 × 12000 mm. At a nominal steel density of 7850 kg/m³, calculated mass is approximately 1413 kg per piece. Actual weighing, dimensional tolerances, grade and inspection requirements must be agreed before ordering. 12 × 1250 × 12000 mm
Hot-rolled sheet and coil 12 × 1250 × 12000 mm Technical and buying guide
EMRA Steel
Review Hot-rolled sheet and coil for the 12 × 1250 × 12000 mm specification. Check material grade, dimensions, inspection documents and delivery requirements before requesting a quotation.Read more
Standards and applicability
Distinguish structural grades to EN 10025-2 from DD11/DD12 forming grades to EN 10111; EN 10051 addresses the applicable hot-strip dimensional tolerances. DD11/DD12 mechanical references are restricted to 3–11 mm and transverse specimens, with A5 for thickness above 3 mm; a 12 mm request has no numeric DD mechanical values here. Specify coil or sheet, surface, edges, coil bore/mass and cut length separately.
Mechanical reference table
Mechanical reference table
Grade / material
Scope / condition
Re / Rp0.2 (MPa)
Rm (MPa)
A min. (%)
Impact reference
S235JR
3 < t ≤ 16 mm
≥235
360–510
—
27 J / +20°C
S355J2
3 < t ≤ 16 mm
≥355
470–630
—
27 J / −20°C
DD11
3 < t ≤ 11 mm
—
—
—
—
DD12
3 < t ≤ 11 mm
—
—
—
—
Chemical composition references
Chemical composition references
Grade / material
Scope / condition
C (%)
Mn (%)
Si (%)
P (%)
S (%)
Cr / CEV (%)
S235JR
3 < t ≤ 16 mm
≤0.17
≤1.40
—
≤0.035
≤0.035
—
S355J2
3 < t ≤ 16 mm
≤0.20
≤1.60
≤0.55
≤0.025
≤0.025
—
DD11
EN 10111
≤0.12
≤0.60
—
≤0.045
≤0.045
—
DD12
EN 10111
≤0.10
≤0.45
—
≤0.035
≤0.035
—
Selected percentages by mass and test values are reference requirements within the stated scope, not the actual heat analysis or a complete specification. A dash means no value is declared here, not zero. Compare the offered heat and test results with the applicable specification and inspection document. If EN 10204 type 3.1 is required, agree document availability, heat traceability and test scope before ordering.
Inspection and export enquiry
Send the exact product, size, full grade and standard edition, delivery condition, quantity, test requirements and named destination. Confirm cutting, coating, bundle or coil mass, protection, unloading and the Incoterms delivery point in the quotation. The destination guidance below supports port and inland comparisons; it does not confirm local stock or a fixed price.
Chemistry references and commercial grades
St37, St44 and St52 · historical DIN 17100 reference
Ladle-analysis reference for St37-2, St44-2 and St52-3 at t ≤16 mm only. Bare St37/St44/St52 names need a suffix, edition and delivery condition. Other thicknesses and product analysis have different rules. These legacy grades are not automatically equivalent to EN grades or interchangeable with CK45/CK60. For semi-finished feedstock, agree chemistry and downstream qualification separately.
St37, St44 and St52 · historical DIN 17100 reference
Grade / commercial type
C (%)
Mn (%)
Si (%)
P (%)
S (%)
St37-2 / 1.0037
≤0.17
—
—
≤0.050
≤0.050
St44-2 / 1.0044
≤0.21
—
—
≤0.050
≤0.050
St52-3 / 1.0570
≤0.20
≤1.60
≤0.55
≤0.040
≤0.040
Reference values are not shipment analysis or an inventory promise. Agree the complete specification, sampling basis, test methods and acceptance limits before ordering; confirm actual results on the heat/lot certificate. A dash means no numeric limit is stated in this selected reference, not zero.
Size specifications: Hot-rolled sheet and coil 12 × 1250 × 12000 mm
Reference dimensions: 12 × 1250 × 12000 mm. At a nominal steel density of 7850 kg/m³, calculated mass is approximately 1413 kg per piece. Actual weighing, dimensional tolerances, grade and inspection requirements must be agreed before ordering. 12 × 1250 × 12000 mm
Hot-Rolled Sheet 12 × 1250 × 12000 mm Price by Grade: S235JR, S355J2, DD11, DD12, St37, St44, St52
The values below come from this page's reference tables and are not guaranteed; state the standard and grade when you ask for a price.
Hot-Rolled Sheet 12 × 1250 × 12000 mm S235JR Price per Ton
S235JR (3 < t ≤ 16 mm): C 0.17 max, Mn 1.40 max, P 0.035 max, S 0.035 max; Re 235 MPa min, Rm 360–510 MPa, impact 27 J / +20°C. State tonnage and the receiving city or port. Enquiries from Uzbekistan are quoted on a stated delivery basis.
Reference values for S355J2 (3 < t ≤ 16 mm): C 0.20 max, Mn 1.60 max, Si 0.55 max, P 0.025 max, S 0.025 max; Re 355 MPa min, Rm 470–630 MPa, impact 27 J / −20°C. Include packing and loading limits. Quotations are available for UAE.
DD11 / DD12: DD11 (EN 10111): C 0.12 max, Mn 0.60 max, P 0.045 max, S 0.045 max; DD12 (EN 10111): C 0.10 max, Mn 0.45 max, P 0.035 max, S 0.035 max. Name the standard and edition in the enquiry. It can be quoted for Oman buyers.
Hot-Rolled Sheet 12 × 1250 × 12000 mm St37, St44, St52 Price per Ton
St37, St44, St52: St37-2: C 0.17 max, P 0.050 max, S 0.050 max; St44-2: C 0.21 max, P 0.050 max, S 0.050 max; St52-3: C 0.20 max, Mn 1.60 max, Si 0.55 max, P 0.040 max, S 0.040 max. Send tonnage and size for a price. Enquiries from Georgia are quoted on a stated delivery basis.
Choosing this specification
For 12 × 1250 × 12000 mm, agree the dimension order and whether the material is supplied as coil or cut lengths. Check usable width, cutting layout and flatness before comparing yield; nominal geometry does not include trimming or process losses. At nominal geometry and 7850 kg/m³ steel density, the reference is 1413.000 kg per piece. This calculation excludes tolerances, coatings, corner radii and process losses; it is not certified shipping weight or a load rating.
Hot-Rolled Sheet 12 × 1250 × 12000 mm St37 Supplier in Georgia and Tbilisi
EMRA Steel is headquartered in Tbilisi and supplies Hot-Rolled Sheet 12 × 1250 × 12000 mm to buyers across Georgia. Offers cover delivery to Tbilisi, Rustavi and Kutaisi, or a port handover at Poti or Batumi. State grade and tonnage with your enquiry, together with sheet or coil form, width and coil weight. See the Georgia market guide. Available grades: S235JR, S355J2, DD11, DD12, St37, St44 and St52.
Hot-Rolled Sheet 12 × 1250 × 12000 mm St44 Price in Georgia
The Hot-Rolled Sheet 12 × 1250 × 12000 mm price in Georgia depends on grade, quantity and the delivery basis, as well as sheet or coil form, width and coil weight. A Poti or Batumi port price and a delivered price to Rustavi or Kutaisi cover different transport scopes, so compare offers on the same basis.
Hot-Rolled Sheet 12 × 1250 × 12000 mm St52 Price in Tbilisi
For Hot-Rolled Sheet 12 × 1250 × 12000 mm delivered to Tbilisi, the quotation names the receiving address, the inland leg from Poti or Batumi and the unloading equipment on site. Request a quotation with grade, tonnage and your Tbilisi address.
Hot-Rolled Sheet 12 × 1250 × 12000 mm S235JR Supplier in UAE and Dubai
EMRA Steel has a registered office in Dubai and supplies Hot-Rolled Sheet 12 × 1250 × 12000 mm to buyers across the UAE. Offers cover delivery to Dubai, Sharjah and Abu Dhabi, or a port handover at Jebel Ali or Khalifa Port. State grade and tonnage with your enquiry, together with sheet or coil form, width and coil weight. See the UAE market guide. Available grades: S235JR, S355J2, DD11, DD12, St37, St44 and St52.
Hot-Rolled Sheet 12 × 1250 × 12000 mm S355J2 Price in UAE
The Hot-Rolled Sheet 12 × 1250 × 12000 mm price in the UAE depends on grade, quantity and the delivery basis, as well as sheet or coil form, width and coil weight. A Jebel Ali or Khalifa Port price and a delivered price to Sharjah or Abu Dhabi cover different transport scopes, so compare offers on the same basis.
Hot-Rolled Sheet 12 × 1250 × 12000 mm DD11 Price in Dubai
For Hot-Rolled Sheet 12 × 1250 × 12000 mm delivered in Dubai, the quotation names the site or warehouse address, the trucking scope from Jebel Ali and the unloading equipment on site. Request a quotation with grade, tonnage and your Dubai address.
Buy Hot-Rolled Sheet 12 × 1250 × 12000 mm: Price and Quotation by Destination
Hot-Rolled Sheet 12 × 1250 × 12000 mm weighs 1413.000 kg per piece on the page reference. Send grade, tonnage and piece count, and name the city or port you want the price for.
Hot-Rolled Sheet 12 × 1250 × 12000 mm Price in UAE
UAE offers can be port-based or delivered by road. See the UAE. Name the grade and tonnage for Hot-Rolled Sheet 12 × 1250 × 12000 mm in your request.
Hot-Rolled Sheet 12 × 1250 × 12000 mm Price in Dubai
Our Dubai office can discuss the specification before a Dubai price is issued. Name the unloading equipment when you ask for the Hot-Rolled Sheet 12 × 1250 × 12000 mm price.
Request Hot-Rolled Sheet 12 × 1250 × 12000 mm Offer for Sharjah
Sharjah uses the same specification, with the trucking scope stated. Send the receiving address with your Hot-Rolled Sheet 12 × 1250 × 12000 mm tonnage.
Hot-Rolled Sheet 12 × 1250 × 12000 mm Price via Jebel Ali
A Jebel Ali price names the terminal basis and the discharge scope. Ask for a port-based Hot-Rolled Sheet 12 × 1250 × 12000 mm basis next to a delivered one.
Hot-Rolled Sheet 12 × 1250 × 12000 mm St52 Supplier and Price for Qatar and Doha
Offers for Qatar depend on the documents the buyer lists. See Qatar. Name the grade and tonnage for Hot-Rolled Sheet 12 × 1250 × 12000 mm in your request.
Request Hot-Rolled Sheet 12 × 1250 × 12000 mm Offer for Doha
Doha offers depend on the documents the buyer lists. Send the receiving address with your Hot-Rolled Sheet 12 × 1250 × 12000 mm tonnage.
Hot-Rolled Sheet 12 × 1250 × 12000 mm Price via Hamad Port
A Hamad Port price separates port charges from the steel price. Ask for a port-based Hot-Rolled Sheet 12 × 1250 × 12000 mm basis next to a delivered one.
Hot-Rolled Sheet 12 × 1250 × 12000 mm S235JR Supplier and Price for Oman and Muscat
Offers for Oman can be port-based at Sohar or delivered to Muscat. See the Oman destination guide. Send tonnage, grade and the delivery point for Hot-Rolled Sheet 12 × 1250 × 12000 mm.
Hot-Rolled Sheet 12 × 1250 × 12000 mm Quotation for Muscat
For Muscat the delivery basis comes first in the quotation. Send the receiving address with your Hot-Rolled Sheet 12 × 1250 × 12000 mm tonnage.
Request Hot-Rolled Sheet 12 × 1250 × 12000 mm via Sohar
Sohar cargo is quoted with port handover. Name the terminal and discharge terms in your Hot-Rolled Sheet 12 × 1250 × 12000 mm request.
Hot-Rolled Sheet 12 × 1250 × 12000 mm DD12 Supplier and Price for Kuwait and Kuwait City
Offers for Kuwait state the port handover and handling limits. See Kuwait. Send tonnage, grade and the delivery point for Hot-Rolled Sheet 12 × 1250 × 12000 mm.
Buy Hot-Rolled Sheet 12 × 1250 × 12000 mm in Kuwait City
Kuwait City offers state the yard handling limits for heavy coils and sheets. Name the unloading equipment when you ask for the Hot-Rolled Sheet 12 × 1250 × 12000 mm price.
Buy Hot-Rolled Sheet 12 × 1250 × 12000 mm via Shuwaikh Port
A Shuwaikh Port price names the handover point and discharge terms. Name the terminal and discharge terms in your Hot-Rolled Sheet 12 × 1250 × 12000 mm request.
Hot-Rolled Sheet 12 × 1250 × 12000 mm Price in Georgia
Black Sea ports and inland cities can both be quoted. See Georgia. Send tonnage, grade and the delivery point for Hot-Rolled Sheet 12 × 1250 × 12000 mm.
Hot-Rolled Sheet 12 × 1250 × 12000 mm Price in Tbilisi
Delivery to Tbilisi is quoted against the unloading equipment and truck access at your site. Name the unloading equipment when you ask for the Hot-Rolled Sheet 12 × 1250 × 12000 mm price.
Request Hot-Rolled Sheet 12 × 1250 × 12000 mm Offer for Kutaisi
For Kutaisi the inland leg from the port or border is shown as its own line. Send the receiving address with your Hot-Rolled Sheet 12 × 1250 × 12000 mm tonnage.
Request Hot-Rolled Sheet 12 × 1250 × 12000 mm via Batumi
A Batumi-based offer names the port basis and who handles discharge of heavy coils and sheets. Ask for a port-based Hot-Rolled Sheet 12 × 1250 × 12000 mm basis next to a delivered one.
Buy Hot-Rolled Sheet 12 × 1250 × 12000 mm via Poti Port
Poti is the second Black Sea option; the offer says which port the price uses. Name the terminal and discharge terms in your Hot-Rolled Sheet 12 × 1250 × 12000 mm request.
Hot-Rolled Sheet 12 × 1250 × 12000 mm S355J2 Supplier and Price for Armenia and Yerevan
Armenia has no sea port, so quotations define the inland route and who handles border formalities. See the Armenia destination guide. Name the grade and tonnage for Hot-Rolled Sheet 12 × 1250 × 12000 mm in your request.
Request Hot-Rolled Sheet 12 × 1250 × 12000 mm Offer for Yerevan
Yerevan deliveries are inland, so the offer defines the route and border steps. Send the receiving address with your Hot-Rolled Sheet 12 × 1250 × 12000 mm tonnage.
Hot-Rolled Sheet 12 × 1250 × 12000 mm St37 Supplier and Price for Azerbaijan and Baku
The Azerbaijan quotation names who handles customs. See Azerbaijan. Name the grade and tonnage for Hot-Rolled Sheet 12 × 1250 × 12000 mm in your request.
Hot-Rolled Sheet 12 × 1250 × 12000 mm Quotation for Baku
A Baku quotation can use a handover near the city or delivery to your site. Send the receiving address with your Hot-Rolled Sheet 12 × 1250 × 12000 mm tonnage.
Hot-Rolled Sheet 12 × 1250 × 12000 mm St44 Supplier and Price for Uzbekistan and Tashkent
Uzbekistan is landlocked, so offers fix grade and size together with the rail or road leg. See the Uzbekistan destination guide. Name the grade and tonnage for Hot-Rolled Sheet 12 × 1250 × 12000 mm in your request.
Buy Hot-Rolled Sheet 12 × 1250 × 12000 mm in Tashkent
Tashkent quotations name the receiving station or site and the wagon or truck type, which matters for heavy coils and sheets. Name the unloading equipment when you ask for the Hot-Rolled Sheet 12 × 1250 × 12000 mm price.
Hot-Rolled Sheet 12 × 1250 × 12000 mm Price in Bukhara
Route and handover for Bukhara are confirmed before a delivered price. Name the unloading equipment when you ask for the Hot-Rolled Sheet 12 × 1250 × 12000 mm price.
Hot-Rolled Sheet 12 × 1250 × 12000 mm DD11 Supplier and Price for Turkmenistan and Ashgabat
Turkmen enquiries can use a Caspian port or an inland receiving point. See Turkmenistan. Send tonnage, grade and the delivery point for Hot-Rolled Sheet 12 × 1250 × 12000 mm.
Hot-Rolled Sheet 12 × 1250 × 12000 mm Price in Ashgabat
An Ashgabat offer names the handover and the documents required. Name the unloading equipment when you ask for the Hot-Rolled Sheet 12 × 1250 × 12000 mm price.
Request Hot-Rolled Sheet 12 × 1250 × 12000 mm via Turkmenbashi
Turkmenbashi can be quoted as a Caspian port handover. Ask for a port-based Hot-Rolled Sheet 12 × 1250 × 12000 mm basis next to a delivered one.
Buying Hot-rolled sheet and coil 12 × 1250 × 12000 mm and requesting a price
The price for Hot-rolled sheet and coil 12 × 1250 × 12000 mm depends on the material specification, quantity, production or processing requirements, inspection, packing, freight and delivery schedule. Compare offers on the same technical specification and delivery basis; confirm availability and quotation validity before ordering.
For buying and price enquiries for Hot-rolled sheet and coil 12 × 1250 × 12000 mm, specify your delivery destination: Georgia (including Tbilisi), Turkey (including Ankara and Istanbul), the United Arab Emirates (UAE, including Dubai), Kuwait, Oman or Qatar. Send the required quantity, grade or chemical analysis, dimensions and inspection scope. Freight, delivery terms and shipment timing affect the quotation; supply options and destination documentation require confirmation before an order is agreed.
Preparing an enquiry for Hot-rolled sheet and coil 12 × 1250 × 12000 mm
Include Hot-rolled sheet and coil 12 × 1250 × 12000 mm, the required grade and complete standard designation, order quantity, length or coil limits where applicable, inspection documents and the exact delivery destination. Confirm traceability, packing, commercial terms and the shipment schedule with EMRA Steel.
Choose the product specification first; destination and shipment details belong in the delivery enquiry. Destination enquiry guides
Grade enquiries for Hot-rolled sheet and coil 12 × 1250 × 12000 mm
Hot-rolled sheet and coil 12 × 1250 × 12000 mm S235JR
For Hot-rolled sheet and coil 12 × 1250 × 12000 mm S235JR, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
Hot-rolled sheet and coil 12 × 1250 × 12000 mm S355J2
For Hot-rolled sheet and coil 12 × 1250 × 12000 mm S355J2, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
Hot-rolled sheet and coil 12 × 1250 × 12000 mm DD11
For Hot-rolled sheet and coil 12 × 1250 × 12000 mm DD11, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
Hot-rolled sheet and coil 12 × 1250 × 12000 mm DD12
For Hot-rolled sheet and coil 12 × 1250 × 12000 mm DD12, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
