Compare section dimensions, steel grades and supply options.
Equal angles
Request equal-leg steel angles for project-specified frames, bracing and fabricated connections. Compare all 29 catalogue sizes, select the material grade and dimensional standard, and send the required length, quantity and destination. Manufacturing route, grade, packing, inspection documents and delivery feasibility are confirmed with the offer; the catalogue is not a stock list.
Equal Angle Section and Weight Comparison
The table shows size, geometric weight per metre, geometric weight per 12 m bar and guide/enquiry actions. Weights use nominal dimensions and density 7850 kg/m³, excluding radii and rolling tolerances. They are planning estimates, not certified shipment weights or stock confirmations.
Request equal-leg steel angles for project-specified frames, bracing and fabricated connections. Compare all 29 catalogue sizes, select the material grade and dimensional standard, and send the required length, quantity and destination. Manufacturing route, grade, packing, inspection documents and delivery feasibility are confirmed with the offer; the catalogue is not a stock list.Read more
Dimensions, Material Grade and Legacy Designations
EN 10056-1 addresses section dimensions and EN 10056-2 tolerances; EN 10025-2 addresses structural steel material requirements. Agree whether the requested size and manufacturing route fall within the chosen standard, especially for thin 2.5/3.5 mm enquiries. S235JR, S275JR, S355JR and S355J2 are distinct grade references, not confirmed stock. ST37, ST52 and 5SP need their complete specification, suffix, edition and acceptance requirements; no automatic EN equivalence or shared numerical chemistry is assigned.
Structural Grade Mechanical References
The following published section-grade references use EN 10025-2:2019. Yield values apply to nominal thickness t ≤ 16 mm; the displayed tensile and elongation values are restricted here to 3 ≤ t ≤ 15 mm. Do not apply them to the 2.5 mm catalogue entries without checking their applicable thickness range. Elongation uses L0 = 5.65√S0; confirm sampling, orientation and acceptance rules. The JR impact reference is 27 J at +20°C, while J2 is 27 J at −20°C. Impact testing, specimen size and applicability to thin sections must be agreed under the actual standard and order; the table does not certify a shipment or structural design.
Structural Grade Mechanical References
Grade
ReH min. (MPa), t ≤ 16 mm
Rm (MPa), 3 ≤ t ≤ 15 mm
A min. (%), 3 ≤ t ≤ 15 mm
Impact reference
S235JR
235
360–510
26
27 J / +20°C
S275JR
275
410–560
23
27 J / +20°C
S355JR
355
470–630
22
27 J / +20°C
S355J2
355
470–630
22
27 J / −20°C
Chemical Composition and CEV References
Selected ladle-analysis maxima below come from one published section-grade table referencing EN 10025-2:2019: carbon for t ≤ 16 mm and CEV for t ≤ 30 mm. Values are percentages by mass, not actual heat analysis, a complete normative specification or confirmed EMRA material. A dash for silicon means the reference sets no displayed general limit; it is not zero. Purchase requirements, product-analysis tolerances and the standard edition must be checked separately. For galvanizing category B, the reference requires separately agreed Si 0.14–0.25% and P ≤ 0.035%; do not assume galvanizing suitability from grade alone.
Chemical Composition and CEV References
Grade
C max. (%)
Mn max. (%)
Si max. (%)
P max. (%)
S max. (%)
CEV max. (%)
S235JR
0.17
1.40
—
0.040
0.040
0.35
S275JR
0.21
1.50
—
0.040
0.040
0.40
S355JR
0.24
1.60
0.55
0.040
0.040
0.45
S355J2
0.20
1.60
0.55
0.030
0.030
0.45
Compare the actual heat analysis and agreed test results with the mill inspection document. If EN 10204 type 3.1 is required, confirm document availability, heat traceability and test scope before ordering. CEV = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15; weldability still requires the appropriate procedure and project acceptance.
Packing, Processing and Export Enquiries
Request bundle mass, strapping, lifting points, dunnage and corrosion protection for the actual shipment. Cutting, drilling, primer or hot-dip galvanizing must be specified and confirmed rather than assumed available. Include quantity, length, grade, dimensional acceptance, inspection documents and a named city or port. FOB names a shipment port; CFR/CIF name a destination port and DAP a destination place under Incoterms 2020. The regional sections retain Poti/Tbilisi, Jebel Ali/Dubai, Ambarlı/Istanbul, Shuwaikh/Shuaiba, Sohar/Muscat and Hamad Port/Doha; routing and unloading are subject to confirmation. Grade, size, processing, quantity, testing, packing and freight affect the quotation; no fixed unit price or universal bundle weight is promised.
Chemistry references and commercial grades
St37, St44 and St52 · historical DIN 17100 reference
Ladle-analysis reference for St37-2, St44-2 and St52-3 at t ≤16 mm only. Bare St37/St44/St52 names need a suffix, edition and delivery condition. Other thicknesses and product analysis have different rules. These legacy grades are not automatically equivalent to EN grades or interchangeable with CK45/CK60. For semi-finished feedstock, agree chemistry and downstream qualification separately.
St37, St44 and St52 · historical DIN 17100 reference
Grade / commercial type
C (%)
Mn (%)
Si (%)
P (%)
S (%)
St37-2 / 1.0037
≤0.17
—
—
≤0.050
≤0.050
St44-2 / 1.0044
≤0.21
—
—
≤0.050
≤0.050
St52-3 / 1.0570
≤0.20
≤1.60
≤0.55
≤0.040
≤0.040
Reference values are not shipment analysis or an inventory promise. Agree the complete specification, sampling basis, test methods and acceptance limits before ordering; confirm actual results on the heat/lot certificate. A dash means no numeric limit is stated in this selected reference, not zero.
Equal angles Technical and buying guide
Equal-leg steel angles for frames, bracing and fabricated connections. Compare leg dimensions, thicknesses and bar weights before requesting a quotation.
Equal angles have two equal legs and an L-shaped section, used in frameworks and fabrication.
Specification and dimensions
Equal angles: leg a × leg b × thickness, followed by length. Example: 40 × 40 × 3 mm, 6 m. For an equal angle the two legs are equal; specify the size standard and tolerances.
Grades and applicable standards
Reference standards: EN 10056-1 / EN 10056-2 / EN 10025-2. State the complete material grade and standard edition separately. Dimensional standards do not establish grade equivalence. For structural steel enquiries, S235JR or S355JR may be specified where appropriate to the governing material specification; other applications require their own agreed grade.
Applications and project requirements
Equal angles are used in bracing, frames, towers and fabricated connections subject to the project design. Specify hole patterns, cutting and galvanizing requirements where applicable.
Inspection and traceability
Agree heat or batch identification, chemical analysis, applicable tests and dimensional checks before ordering. Specify inspection documents, acceptance criteria and any independent inspection requirements.
Specify EN 10056-1 for dimensions and EN 10056-2 for tolerances. Material enquiries may specify S235JR, S275JR or S355J2 to EN 10025-2, subject to confirmation. For requests using ST37/ST52, DIN 17100, 5SP or ISIRI 13968-1, provide the complete grade, applicable standard and edition, and required inspection certificate; these designations are not automatically interchangeable or confirmation of EMRA Steel stock.
Limits are published reference values from this page's tables, not guaranteed values; confirm the full standard designation in your enquiry.
Buy Equal Angle S235JR
S235JR is the base structural grade here (C 0.17 max, Mn 1.40 max, ReH min 235 MPa) and the usual starting point for ordinary structural work. Send tonnage and bar length for a price. It can be quoted for Georgia buyers.
Equal Angle S275JR Price per Ton
S275JR raises the limits to C 0.21 max and Mn 1.50 max with ReH min 275 MPa for more demanding frames. State tonnage and the receiving city or port. Enquiries from Azerbaijan are quoted on a stated delivery basis.
Request Equal Angle S355JR Quotation
S355JR (C 0.24 max, Mn 1.60 max, Si 0.55 max, ReH min 355 MPa) is chosen where a higher-strength angle is specified. Include bundle and loading limits. Quotations are available for Turkmenistan.
Buy Equal Angle S355J2
S355J2 keeps the 355 MPa yield with tighter P and S at 0.030 max (C 0.20 max, Mn 1.60 max, Si 0.55 max) and a 27 J impact reference at −20°C. Name the standard and edition in the enquiry. It can be quoted for Qatar buyers.
Equal Angle ST37 Price per Ton
ST37 is enquired as St37-2 / 1.0037 (C 0.17 max, P and S 0.050 max), a historical designation. Send tonnage and bar length for a price. Enquiries from Kuwait are quoted on a stated delivery basis.
Request Equal Angle ST52 Quotation
ST52 is enquired as St52-3 / 1.0570 (C 0.20 max, Mn 1.60 max, Si 0.55 max, P and S 0.040 max). State tonnage and the receiving city or port. Quotations are available for Armenia.
Buy Equal Angle 5SP
5SP is a regional designation with no limits tabulated on this page, so state the exact standard and chemistry you need. Include bundle and loading limits. It can be quoted for Uzbekistan buyers.
Equal Angle Supplier in Georgia and Tbilisi
EMRA Steel is headquartered in Tbilisi and supplies Equal Angle to buyers across Georgia. Offers cover delivery to Tbilisi, Rustavi and Kutaisi, or a port handover at Poti or Batumi. State grade and tonnage with your enquiry, together with bar length, bundle weight and lifting limits. See the Georgia market guide.
Equal Angle Price in Georgia
The Equal Angle price in Georgia depends on grade, quantity and the delivery basis, as well as bar length, bundle weight and lifting limits. A Poti or Batumi port price and a delivered price to Rustavi or Kutaisi cover different transport scopes, so compare offers on the same basis.
Equal Angle Price in Tbilisi
For Equal Angle delivered to Tbilisi, the quotation names the receiving address, the inland leg from Poti or Batumi and the unloading equipment on site. Request a quotation with grade, tonnage and your Tbilisi address.
Equal Angle Supplier in UAE and Dubai
EMRA Steel has a registered office in Dubai and supplies Equal Angle to buyers across the UAE. Offers cover delivery to Dubai, Sharjah and Abu Dhabi, or a port handover at Jebel Ali or Khalifa Port. State grade and tonnage with your enquiry, together with bar length, bundle weight and lifting limits. See the UAE market guide.
Equal Angle Price in UAE
The Equal Angle price in the UAE depends on grade, quantity and the delivery basis, as well as bar length, bundle weight and lifting limits. A Jebel Ali or Khalifa Port price and a delivered price to Sharjah or Abu Dhabi cover different transport scopes, so compare offers on the same basis.
Equal Angle Price in Dubai
For Equal Angle delivered in Dubai, the quotation names the site or warehouse address, the trucking scope from Jebel Ali and the unloading equipment on site. Request a quotation with grade, tonnage and your Dubai address.
Buy Equal Angle: Price and Quotation by Destination
EMRA Steel quotes equal leg angles from 30 × 30 × 3 to 150 × 150 × 15 mm for nine destination markets. Each offer states grade, section size, bar length, bundling and whether the price is port-based or delivered to a named city.
Buy Equal Angle for Georgia
Our Tbilisi head office handles Georgian enquiries. See the Georgia destination guide. Name the grade and tonnage in your request.
Buy Equal Angle in Tbilisi
Tbilisi enquiries go to our head office, so bar lengths, bundling and loading can be agreed directly. Name the unloading equipment when you ask for the price.
Equal Angle Price in Kutaisi
For Kutaisi the inland leg from the port or border is shown as its own line. Send the receiving address with your tonnage.
Buy Equal Angle via Batumi
Batumi can serve as the sea entry, with discharge terms written next to the price. Name the terminal and discharge terms in your request.
Equal Angle Price via Poti Port
Poti is the second Black Sea option; the offer says which port the price uses. Ask for a port-based basis next to a delivered one.
Equal Angle Price in Armenia
Armenia has no sea port, so quotations define the inland route and who handles border formalities. See the Armenia destination guide. Name the grade and tonnage in your request.
Equal Angle Price in Yerevan
Yerevan deliveries are inland, so the offer defines the route and border steps. Send the receiving address with your tonnage.
Request Equal Angle Quotation for Azerbaijan
Offers state the handover point and the customs scope. See the Azerbaijan destination guide. Name the grade and tonnage in your request.
Request Equal Angle Offer for Baku
Baku offers fix the handover point and customs scope before the price. Name the unloading equipment when you ask for the price.
Equal Angle for Uzbekistan: Price and Offer
Uzbekistan is landlocked, so offers fix grade and bar length together with the rail or road leg. See the Uzbekistan destination guide. Name the grade and tonnage in your request.
Equal Angle Quotation for Tashkent
Tashkent quotations name the receiving station or site and the wagon or truck type, which matters for 12 m bars. Send the receiving address with your tonnage.
Buy Equal Angle in Bukhara
Bukhara offers state the inland distance and transit steps first. Name the unloading equipment when you ask for the price.
Buy Equal Angle for Turkmenistan
Offers state a clear handover point. See the Turkmenistan destination guide. Name the grade and tonnage in your request.
Buy Equal Angle in Ashgabat
Ashgabat can be priced as a delivered offer from a stated receiving point. Name the unloading equipment when you ask for the price.
Buy Equal Angle via Turkmenbashi
Turkmenbashi can be quoted as a Caspian port handover. Ask for a port-based basis next to a delivered one.
Equal Angle Price in the UAE
Our Dubai office supports specification questions for the UAE. See the UAE destination guide. Name the grade and tonnage in your request.
Equal Angle Price in Dubai
Dubai enquiries are handled with our Dubai office for specification questions. Send the receiving address with your tonnage.
Request Equal Angle Offer for Sharjah
Sharjah uses the same specification, with the trucking scope stated. Name the unloading equipment when you ask for the price.
Request Equal Angle via Jebel Ali
Jebel Ali quotes show port handover and discharge terms. Ask for a port-based basis next to a delivered one.
Request Equal Angle Quotation for Qatar
Offers for Qatar depend on the documents the buyer lists. See Qatar. Name the grade and tonnage in your request.
Request Equal Angle Offer for Doha
Doha offers depend on the documents the buyer lists. Name the unloading equipment when you ask for the price.
Request Equal Angle via Hamad Port
Hamad Port handover is the stated basis for port-based offers. Ask for a port-based basis next to a delivered one.
Equal Angle for Oman: Price and Offer
Omani quotations name the discharge port and the terms. See Oman. Name the grade and tonnage in your request.
Equal Angle Quotation for Muscat
Muscat offers state the discharge port and terms before the price. Send the receiving address with your tonnage.
Buy Equal Angle via Sohar
Sohar cargo is quoted with port handover. Name the terminal and discharge terms in your request.
Buy Equal Angle for Kuwait
Offers for Kuwait state the port handover and handling limits. See Kuwait. Name the grade and tonnage in your request.
Buy Equal Angle in Kuwait City
Kuwait City offers state the yard handling limits for long bars. Name the unloading equipment when you ask for the price.
Equal Angle Price via Shuwaikh Port
Port handover and discharge scope at Shuwaikh are shown in the offer. Ask for a port-based basis next to a delivered one.
Sizes, weights and quotation guidance
30 × 30 × 3 mm
Equal-leg angle 30 × 30 × 3 mm: each leg is 30 mm (3 cm) wide and the requested thickness is 3 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 1.342 kg/m, or 8.05 kg for 6 m and 16.1 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 30 × 30 × 3 mm
40 × 40 × 2.5 mm
Equal-leg angle 40 × 40 × 2.5 mm: each leg is 40 mm (4 cm) wide and the requested thickness is 2.5 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 1.521 kg/m, or 9.13 kg for 6 m and 18.25 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 40 × 40 × 2.5 mm
40 × 40 × 3 mm
Equal-leg angle 40 × 40 × 3 mm: each leg is 40 mm (4 cm) wide and the nominal leg thickness is 3 mm. Enquiry lengths: 6 m and 12 m, subject to supply confirmation. Reference mass: approximately 1.85 kg/m; calculated bar weights are 11.1 kg for 6 m and 22.2 kg for 12 m. Actual weight varies with rolling tolerances; confirm the supplier’s section table and weighing basis. 40 × 40 × 3 mm
40 × 40 × 4 mm
Equal-leg angle 40 × 40 × 4 mm: each leg is 40 mm (4 cm) wide and the requested thickness is 4 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 2.386 kg/m, or 14.32 kg for 6 m and 28.63 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 40 × 40 × 4 mm
50 × 50 × 2.5 mm
Equal-leg angle 50 × 50 × 2.5 mm: each leg is 50 mm (5 cm) wide and the requested thickness is 2.5 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 1.913 kg/m, or 11.48 kg for 6 m and 22.96 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 50 × 50 × 2.5 mm
50 × 50 × 3 mm
Equal-leg angle 50 × 50 × 3 mm: each leg is 50 mm (5 cm) wide and the requested thickness is 3 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 2.284 kg/m, or 13.7 kg for 6 m and 27.41 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 50 × 50 × 3 mm
50 × 50 × 3.5 mm
Equal-leg angle 50 × 50 × 3.5 mm: each leg is 50 mm (5 cm) wide and the requested thickness is 3.5 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 2.651 kg/m, or 15.91 kg for 6 m and 31.81 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 50 × 50 × 3.5 mm
50 × 50 × 4 mm
Equal-leg angle 50 × 50 × 4 mm: each leg is 50 mm (5 cm) wide and the requested thickness is 4 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 3.014 kg/m, or 18.08 kg for 6 m and 36.17 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 50 × 50 × 4 mm
50 × 50 × 5 mm
Equal-leg angle 50 × 50 × 5 mm: each leg is 50 mm (5 cm) wide and the nominal leg thickness is 5 mm. Enquiry lengths: 6 m and 12 m, subject to supply confirmation. Reference mass: approximately 3.77 kg/m; calculated bar weights are 22.62 kg for 6 m and 45.24 kg for 12 m. Actual weight varies with rolling tolerances; confirm the supplier’s section table and weighing basis. 50 × 50 × 5 mm
60 × 60 × 4 mm
Equal-leg angle 60 × 60 × 4 mm: each leg is 60 mm (6 cm) wide and the requested thickness is 4 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 3.642 kg/m, or 21.85 kg for 6 m and 43.7 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 60 × 60 × 4 mm
60 × 60 × 5 mm
Equal-leg angle 60 × 60 × 5 mm: each leg is 60 mm (6 cm) wide and the requested thickness is 5 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 4.514 kg/m, or 27.08 kg for 6 m and 54.17 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 60 × 60 × 5 mm
60 × 60 × 6 mm
Equal-leg angle 60 × 60 × 6 mm: each leg is 60 mm (6 cm) wide and the nominal leg thickness is 6 mm. Enquiry lengths: 6 m and 12 m, subject to supply confirmation. Reference mass: approximately 5.42 kg/m; calculated bar weights are 32.52 kg for 6 m and 65.04 kg for 12 m. Actual weight varies with rolling tolerances; confirm the supplier’s section table and weighing basis. 60 × 60 × 6 mm
63 × 63 × 5 mm
Equal-leg angle 63 × 63 × 5 mm: each leg is 63 mm (6.3 cm) wide and the requested thickness is 5 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 4.749 kg/m, or 28.49 kg for 6 m and 56.99 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 63 × 63 × 5 mm
63 × 63 × 6 mm
Equal-leg angle 63 × 63 × 6 mm: each leg is 63 mm (6.3 cm) wide and the requested thickness is 6 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 5.652 kg/m, or 33.91 kg for 6 m and 67.82 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 63 × 63 × 6 mm
75 × 75 × 6 mm
Equal-leg angle 75 × 75 × 6 mm: each leg is 75 mm (7.5 cm) wide and the nominal leg thickness is 6 mm. Enquiry lengths: 6 m and 12 m, subject to supply confirmation. Reference mass: approximately 6.85 kg/m; calculated bar weights are 41.1 kg for 6 m and 82.2 kg for 12 m. Actual weight varies with rolling tolerances; confirm the supplier’s section table and weighing basis. 75 × 75 × 6 mm
80 × 80 × 6 mm
Equal-leg angle 80 × 80 × 6 mm: each leg is 80 mm (8 cm) wide and the requested thickness is 6 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 7.253 kg/m, or 43.52 kg for 6 m and 87.04 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 80 × 80 × 6 mm
80 × 80 × 7 mm
Equal-leg angle 80 × 80 × 7 mm: each leg is 80 mm (8 cm) wide and the requested thickness is 7 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 8.407 kg/m, or 50.44 kg for 6 m and 100.88 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 80 × 80 × 7 mm
80 × 80 × 8 mm
Equal-leg angle 80 × 80 × 8 mm: each leg is 80 mm (8 cm) wide and the nominal leg thickness is 8 mm. Enquiry lengths: 6 m and 12 m, subject to supply confirmation. Reference mass: approximately 9.63 kg/m; calculated bar weights are 57.78 kg for 6 m and 115.56 kg for 12 m. Actual weight varies with rolling tolerances; confirm the supplier’s section table and weighing basis. 80 × 80 × 8 mm
100 × 100 × 6 mm
Equal-leg angle 100 × 100 × 6 mm: each leg is 100 mm (10 cm) wide and the requested thickness is 6 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 9.137 kg/m, or 54.82 kg for 6 m and 109.64 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 100 × 100 × 6 mm
100 × 100 × 7 mm
Equal-leg angle 100 × 100 × 7 mm: each leg is 100 mm (10 cm) wide and the requested thickness is 7 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 10.605 kg/m, or 63.63 kg for 6 m and 127.26 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 100 × 100 × 7 mm
100 × 100 × 8 mm
Equal-leg angle 100 × 100 × 8 mm: each leg is 100 mm (10 cm) wide and the requested thickness is 8 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 12.058 kg/m, or 72.35 kg for 6 m and 144.7 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 100 × 100 × 8 mm
100 × 100 × 9 mm
Equal-leg angle 100 × 100 × 9 mm: each leg is 100 mm (10 cm) wide and the requested thickness is 9 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 13.494 kg/m, or 80.96 kg for 6 m and 161.93 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 100 × 100 × 9 mm
100 × 100 × 10 mm
Equal-leg angle 100 × 100 × 10 mm: each leg is 100 mm (10 cm) wide and the nominal leg thickness is 10 mm. Enquiry lengths: 6 m and 12 m, subject to supply confirmation. Reference mass: approximately 15 kg/m; calculated bar weights are 90 kg for 6 m and 180 kg for 12 m. Actual weight varies with rolling tolerances; confirm the supplier’s section table and weighing basis. 100 × 100 × 10 mm
120 × 120 × 8 mm
Equal-leg angle 120 × 120 × 8 mm: each leg is 120 mm (12 cm) wide and the requested thickness is 8 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 14.57 kg/m, or 87.42 kg for 6 m and 174.84 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 120 × 120 × 8 mm
120 × 120 × 10 mm
Equal-leg angle 120 × 120 × 10 mm: each leg is 120 mm (12 cm) wide and the requested thickness is 10 mm. Enquiry lengths: 6 m and 12 m, subject to confirmation. Geometric mass estimate: 18.055 kg/m, or 108.33 kg for 6 m and 216.66 kg for 12 m, using steel density 7850 kg/m³ and nominal area t × (2a − t). This estimate excludes root and toe radii and rolling tolerances; it is not a mill section-table weight. Confirm the size, manufacturing route, applicable dimensional standard and actual weighing basis with the quotation. 120 × 120 × 10 mm
120 × 120 × 12 mm
Equal-leg angle 120 × 120 × 12 mm: each leg is 120 mm (12 cm) wide and the nominal leg thickness is 12 mm. Enquiry lengths: 6 m and 12 m, subject to supply confirmation. Reference mass: approximately 21.6 kg/m; calculated bar weights are 129.6 kg for 6 m and 259.2 kg for 12 m. Actual weight varies with rolling tolerances; confirm the supplier’s section table and weighing basis. 120 × 120 × 12 mm
150 × 150 × 10 mm
Equal-leg angle 150 × 150 × 10 mm: each leg is 150 mm (15 cm) wide and the nominal leg thickness is 10 mm. Enquiry lengths: 6 m and 12 m, subject to supply confirmation. Reference mass: approximately 23 kg/m; calculated bar weights are 138 kg for 6 m and 276 kg for 12 m. Actual weight varies with rolling tolerances; confirm the supplier’s section table and weighing basis. 150 × 150 × 10 mm
150 × 150 × 12 mm
Equal-leg angle 150 × 150 × 12 mm: each leg is 150 mm (15 cm) wide and the nominal leg thickness is 12 mm. Enquiry lengths: 6 m and 12 m, subject to supply confirmation. Reference mass: approximately 27.3 kg/m; calculated bar weights are 163.8 kg for 6 m and 327.6 kg for 12 m. Actual weight varies with rolling tolerances; confirm the supplier’s section table and weighing basis. 150 × 150 × 12 mm
150 × 150 × 15 mm
Equal-leg angle 150 × 150 × 15 mm: each leg is 150 mm (15 cm) wide and the nominal leg thickness is 15 mm. Enquiry lengths: 6 m and 12 m, subject to supply confirmation. Reference mass: approximately 33.8 kg/m; calculated bar weights are 202.8 kg for 6 m and 405.6 kg for 12 m. Actual weight varies with rolling tolerances; confirm the supplier’s section table and weighing basis. 150 × 150 × 15 mm
Frequently asked questions
Does an example mean immediate availability?
No. Examples are enquiry references; stock and delivery must be confirmed for the complete specification.
Can a different grade or standard be substituted?
Only after the proposed material and the project requirements have been technically reviewed.
Quotation requirements
For an angle quotation, provide both leg dimensions, thickness, length, full steel grade and quantity. Cutting, drilling or galvanizing may change the offer. Get a quote
Choose the product specification first; destination and shipment details belong in the delivery enquiry. Destination enquiry guides
Grade enquiries for Equal angles
Equal angles S235JR
For Equal angles S235JR, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
Equal angles S275JR
For Equal angles S275JR, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
Equal angles S355JR
For Equal angles S355JR, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
Equal angles S355J2
For Equal angles S355J2, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
Equal angles ST37
For Equal angles ST37, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
Equal angles ST52
For Equal angles ST52, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
Equal angles 5SP
For Equal angles 5SP, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
